peaktoy48

How to Change a Subaru Spare Key When you lose your Subaru car key, call a locksmith. Usually, they will cut a new key for you at a lower cost than the dealer. Subaru car keys are typically either smart “push-to-start” fob remote keys, or simply metal keys. The Fob key is equipped with an embedded chip that requires reprogramming. Keyless Entry System Key fobs allow you to lock or unlock your Subaru from a distance. It can also unlock the trunk or lift gate of your vehicle. These remotes use the keypad of your car to communicate with the computer in your vehicle. Certain models of Subaru offer a less-known feature called PIN Code Access. It allows you to utilize a personal number sequence to start and open your vehicle. Check your owner's guide to learn how to use this feature if you own a Subaru Forester, Outback Crosstrek, WRX STI or Impreza. It's possible that the battery in the key fob is dying. subaru duplicate key 'll need to do is make sure that the battery is in good condition and you can accomplish this using a handheld remote tester or a basic multimeter that you can find in your garage. Next, you'll want to remove the key fob from its case and look at the circuit board of its transmitter. It will have one or two sets of 8-digit numbers, so make a note of the first set so you will be able to remember it later. After you've done this you can begin programming the key fob at home. The procedure for programming differs based on the make and year of your vehicle, but it's usually simple enough to accomplish by yourself. Key Fobs Subaru's most recent models all come with key fobs that can not only unlock the doors, but also activate your lights, lock your gas cap, and start your car. This last feature is particularly useful if you've encountered yourself at a gas station and your car wouldn't even start because the battery in the key fob has died. If your Subaru is brand new or old, it's likely that the key fob can be replaced without difficulty. Be aware that some of the more modern models, which have their high level technology, might require visiting a dealer. With just a bit of effort and time, you can design your own key fob replacement. Start by examining the transmitter circuit board inside your key fob (instructions for opening the case should be included in the owner's guide). There should be two or more serial numbers with 8 digits each. Write down the initial number series and keep it in your wallet for reference later. Then, get into the driver's seat and close all the doors. Turn the key to start your vehicle and then shut off after 10 turns. Press the lock button on your key fob and then open the door to ensure that all doors work correctly. Close the door, then take the key off. The chime should be heard from your vehicle again to indicate that the key fob has been programmed. Ignition System If your Subaru keys aren't working as they should, it could be due to the fact that the battery is dead. You can replace the battery for your key fob at home if you know how. The replacement battery is inexpensive and simple to locate. If your key fob doesn't respond to your commands, there could be another problem. It is recommended to visit a dealer for a spare key. They'll ensure that the key is genuine Subaru key that's in warranty. It will also be programmed to your vehicle. This is a lot safer and more convenient than purchasing an aftermarket key from a company via the internet. The dealer can also cut keys for you, provided you provide your VIN number as well as proof of ownership. The information provided will be used to encode the replacement key so that it is recognized by your immobilizer. This is a more complicated process than cutting a single key, and the dealership will charge you more. Once the new key has been programmed and you're able to change it over to your existing key. You'll only have five seconds to insert the second key, so it's important to keep a working key on hand. You can take the key off once the security light has stopped flashing, and then test it. Battery Replacement One of the most important advantages that make Subaru fobs so valuable is their ability to switch on your car's power windows as well as sunroof with just a press of the button. However, the battery that is in the Subaru key fob isn't intended to last forever, and will eventually need to be replaced. This quick guide from Capitol Subaru will help you to replace the battery yourself. You'll first need to find the tiny crevice that separates the front and back of your keyfob. You can cut this seam using the flat-head screwdriver, which will reveal the small compartment that contains the battery. Insert the new battery and make sure it is facing up correctly. Remove the old one. Once you've assembled everything and you are ready to use the new key fob for locking in, unlocking, and even starting your vehicle. Always have a spare set keys, especially if one is damaged or lost. A new key can be found at your local auto dealer or you can have one cut from an locksmith. In either case, it's vital to get your key fob functioning properly in the shortest time possible to ensure you drive in a safe manner!